summaryrefslogtreecommitdiff
path: root/drivers/bluetooth
AgeCommit message (Collapse)Author
9 daysBluetooth: btusb: clamp SCO altsetting table indicesPengpeng Hou
btusb_work() maps the number of active SCO links to USB alternate settings through a three-entry lookup table when CVSD traffic uses transparent voice settings. The lookup currently indexes alts[] with data->sco_num - 1 without first constraining sco_num to the number of available table entries. While the table only defines alternate settings for up to three SCO links, data->sco_num comes from hci_conn_num() and is used directly. Cap the lookup to the last table entry before indexing it so the driver keeps selecting the highest supported alternate setting without reading past alts[]. Fixes: baac6276c0a9 ("Bluetooth: btusb: handle mSBC audio over USB Endpoints") Signed-off-by: Pengpeng Hou <pengpeng@iscas.ac.cn> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
9 daysBluetooth: btintel: serialize btintel_hw_error() with hci_req_sync_lockCen Zhang
btintel_hw_error() issues two __hci_cmd_sync() calls (HCI_OP_RESET and Intel exception-info retrieval) without holding hci_req_sync_lock(). This lets it race against hci_dev_do_close() -> btintel_shutdown_combined(), which also runs __hci_cmd_sync() under the same lock. When both paths manipulate hdev->req_status/req_rsp concurrently, the close path may free the response skb first, and the still-running hw_error path hits a slab-use-after-free in kfree_skb(). Wrap the whole recovery sequence in hci_req_sync_lock/unlock so it is serialized with every other synchronous HCI command issuer. Below is the data race report and the kasan report: BUG: data-race in __hci_cmd_sync_sk / btintel_shutdown_combined read of hdev->req_rsp at net/bluetooth/hci_sync.c:199 by task kworker/u17:1/83: __hci_cmd_sync_sk+0x12f2/0x1c30 net/bluetooth/hci_sync.c:200 __hci_cmd_sync+0x55/0x80 net/bluetooth/hci_sync.c:223 btintel_hw_error+0x114/0x670 drivers/bluetooth/btintel.c:254 hci_error_reset+0x348/0xa30 net/bluetooth/hci_core.c:1030 write/free by task ioctl/22580: btintel_shutdown_combined+0xd0/0x360 drivers/bluetooth/btintel.c:3648 hci_dev_close_sync+0x9ae/0x2c10 net/bluetooth/hci_sync.c:5246 hci_dev_do_close+0x232/0x460 net/bluetooth/hci_core.c:526 BUG: KASAN: slab-use-after-free in sk_skb_reason_drop+0x43/0x380 net/core/skbuff.c:1202 Read of size 4 at addr ffff888144a738dc by task kworker/u17:1/83: __hci_cmd_sync_sk+0x12f2/0x1c30 net/bluetooth/hci_sync.c:200 __hci_cmd_sync+0x55/0x80 net/bluetooth/hci_sync.c:223 btintel_hw_error+0x186/0x670 drivers/bluetooth/btintel.c:260 Fixes: 973bb97e5aee ("Bluetooth: btintel: Add generic function for handling hardware errors") Signed-off-by: Cen Zhang <zzzccc427@gmail.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2026-03-19Bluetooth: hci_ll: Fix firmware leak on error pathAnas Iqbal
Smatch reports: drivers/bluetooth/hci_ll.c:587 download_firmware() warn: 'fw' from request_firmware() not released on lines: 544. In download_firmware(), if request_firmware() succeeds but the returned firmware content is invalid (no data or zero size), the function returns without releasing the firmware, resulting in a resource leak. Fix this by calling release_firmware() before returning when request_firmware() succeeded but the firmware content is invalid. Fixes: 371805522f87 ("bluetooth: hci_uart: add LL protocol serdev driver support") Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de> Signed-off-by: Anas Iqbal <mohd.abd.6602@gmail.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2026-03-12Bluetooth: qca: fix ROM version reading on WCN3998 chipsDmitry Baryshkov
WCN3998 uses a bit different format for rom version: [ 5.479978] Bluetooth: hci0: setting up wcn399x [ 5.633763] Bluetooth: hci0: QCA Product ID :0x0000000a [ 5.645350] Bluetooth: hci0: QCA SOC Version :0x40010224 [ 5.650906] Bluetooth: hci0: QCA ROM Version :0x00001001 [ 5.665173] Bluetooth: hci0: QCA Patch Version:0x00006699 [ 5.679356] Bluetooth: hci0: QCA controller version 0x02241001 [ 5.691109] Bluetooth: hci0: QCA Downloading qca/crbtfw21.tlv [ 6.680102] Bluetooth: hci0: QCA Downloading qca/crnv21.bin [ 6.842948] Bluetooth: hci0: QCA setup on UART is completed Fixes: 523760b7ff88 ("Bluetooth: hci_qca: Added support for WCN3998") Reviewed-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com> Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2026-02-26Merge tag 'net-7.0-rc2' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net Pull networking fixes from Paolo Abeni: "Including fixes from IPsec, Bluetooth and netfilter Current release - regressions: - wifi: fix dev_alloc_name() return value check - rds: fix recursive lock in rds_tcp_conn_slots_available Current release - new code bugs: - vsock: lock down child_ns_mode as write-once Previous releases - regressions: - core: - do not pass flow_id to set_rps_cpu() - consume xmit errors of GSO frames - netconsole: avoid OOB reads, msg is not nul-terminated - netfilter: h323: fix OOB read in decode_choice() - tcp: re-enable acceptance of FIN packets when RWIN is 0 - udplite: fix null-ptr-deref in __udp_enqueue_schedule_skb(). - wifi: brcmfmac: fix potential kernel oops when probe fails - phy: register phy led_triggers during probe to avoid AB-BA deadlock - eth: - bnxt_en: fix deleting of Ntuple filters - wan: farsync: fix use-after-free bugs caused by unfinished tasklets - xscale: check for PTP support properly Previous releases - always broken: - tcp: fix potential race in tcp_v6_syn_recv_sock() - kcm: fix zero-frag skb in frag_list on partial sendmsg error - xfrm: - fix race condition in espintcp_close() - always flush state and policy upon NETDEV_UNREGISTER event - bluetooth: - purge error queues in socket destructors - fix response to L2CAP_ECRED_CONN_REQ - eth: - mlx5: - fix circular locking dependency in dump - fix "scheduling while atomic" in IPsec MAC address query - gve: fix incorrect buffer cleanup for QPL - team: avoid NETDEV_CHANGEMTU event when unregistering slave - usb: validate USB endpoints" * tag 'net-7.0-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (72 commits) netfilter: nf_conntrack_h323: fix OOB read in decode_choice() dpaa2-switch: validate num_ifs to prevent out-of-bounds write net: consume xmit errors of GSO frames vsock: document write-once behavior of the child_ns_mode sysctl vsock: lock down child_ns_mode as write-once selftests/vsock: change tests to respect write-once child ns mode net/mlx5e: Fix "scheduling while atomic" in IPsec MAC address query net/mlx5: Fix missing devlink lock in SRIOV enable error path net/mlx5: E-switch, Clear legacy flag when moving to switchdev net/mlx5: LAG, disable MPESW in lag_disable_change() net/mlx5: DR, Fix circular locking dependency in dump selftests: team: Add a reference count leak test team: avoid NETDEV_CHANGEMTU event when unregistering slave net: mana: Fix double destroy_workqueue on service rescan PCI path MAINTAINERS: Update maintainer entry for QUALCOMM ETHQOS ETHERNET DRIVER dpll: zl3073x: Remove redundant cleanup in devm_dpll_init() selftests/net: packetdrill: Verify acceptance of FIN packets when RWIN is 0 tcp: re-enable acceptance of FIN packets when RWIN is 0 vsock: Use container_of() to get net namespace in sysctl handlers net: usb: kaweth: validate USB endpoints ...
2026-02-23Bluetooth: hci_qca: Cleanup on all setup failuresJinwang Li
The setup process previously combined error handling and retry gating under one condition. As a result, the final failed attempt exited without performing cleanup. Update the failure path to always perform power and port cleanup on setup failure, and reopen the port only when retrying. Fixes: 9e80587aba4c ("Bluetooth: hci_qca: Enhance retry logic in qca_setup") Signed-off-by: Jinwang Li <jinwang.li@oss.qualcomm.com> Reviewed-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2026-02-21Convert 'alloc_obj' family to use the new default GFP_KERNEL argumentLinus Torvalds
This was done entirely with mindless brute force, using git grep -l '\<k[vmz]*alloc_objs*(.*, GFP_KERNEL)' | xargs sed -i 's/\(alloc_objs*(.*\), GFP_KERNEL)/\1)/' to convert the new alloc_obj() users that had a simple GFP_KERNEL argument to just drop that argument. Note that due to the extreme simplicity of the scripting, any slightly more complex cases spread over multiple lines would not be triggered: they definitely exist, but this covers the vast bulk of the cases, and the resulting diff is also then easier to check automatically. For the same reason the 'flex' versions will be done as a separate conversion. Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2026-02-21treewide: Replace kmalloc with kmalloc_obj for non-scalar typesKees Cook
This is the result of running the Coccinelle script from scripts/coccinelle/api/kmalloc_objs.cocci. The script is designed to avoid scalar types (which need careful case-by-case checking), and instead replace kmalloc-family calls that allocate struct or union object instances: Single allocations: kmalloc(sizeof(TYPE), ...) are replaced with: kmalloc_obj(TYPE, ...) Array allocations: kmalloc_array(COUNT, sizeof(TYPE), ...) are replaced with: kmalloc_objs(TYPE, COUNT, ...) Flex array allocations: kmalloc(struct_size(PTR, FAM, COUNT), ...) are replaced with: kmalloc_flex(*PTR, FAM, COUNT, ...) (where TYPE may also be *VAR) The resulting allocations no longer return "void *", instead returning "TYPE *". Signed-off-by: Kees Cook <kees@kernel.org>
2026-02-17Merge tag 'tty-7.0-rc1' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty Pull tty / serial driver updates from Greg KH: "Here is the small amount of tty and serial driver updates for 7.0-rc1. Nothing major in here at all, just some driver updates and minor tweaks and cleanups including: - sh-sci serial driver updates - 8250 driver updates - attempt to make the tty ports have their own workqueue, but was reverted after testing found it to have problems on some platforms. This will probably come back for 7.1 after it has been reworked and resubmitted - other tiny tty driver changes All of these have been in linux-next for a while with no reported problems" * tag 'tty-7.0-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (49 commits) Revert "tty: tty_port: add workqueue to flip TTY buffer" tty: tty_port: add workqueue to flip TTY buffer serial: 8250_pci: Remove custom deprecated baud setting routine serial: 8250_omap: Remove custom deprecated baud setting routine dt-bindings: serial: renesas,scif: Document RZ/G3L SoC serial: 8250: omap: set out-of-band wakeup if wakeup pinctrl exists tty: hvc-iucv: Remove KMSG_COMPONENT macro dt-bindings: serial: google,goldfish-tty: Convert to DT schema dt-bindings: serial: sh-sci: Fold single-entry compatibles into enum serial: 8250: 8250_omap.c: Clear DMA RX running status only after DMA termination is done serial: 8250: 8250_omap.c: Add support for handling UART error conditions serial: SH_SCI: improve "DMA support" prompt serial: Kconfig: fix ordering of entries for menu display serial: 8250: fix ordering of entries for menu display serial: imx: change SERIAL_IMX_CONSOLE to bool 8250_men_mcb: drop unneeded MODULE_ALIAS serial: men_z135_uart: drop unneeded MODULE_ALIAS dt-bindings: serial: renesas,rsci: Document RZ/V2H(P) and RZ/V2N SoCs serial: rsci: Convert to FIELD_MODIFY() dt-bindings: serial: 8250: add SpacemiT K3 UART compatible ...
2026-02-11Merge tag 'net-next-7.0' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next Pull networking updates from Paolo Abeni: "Core & protocols: - A significant effort all around the stack to guide the compiler to make the right choice when inlining code, to avoid unneeded calls for small helper and stack canary overhead in the fast-path. This generates better and faster code with very small or no text size increases, as in many cases the call generated more code than the actual inlined helper. - Extend AccECN implementation so that is now functionally complete, also allow the user-space enabling it on a per network namespace basis. - Add support for memory providers with large (above 4K) rx buffer. Paired with hw-gro, larger rx buffer sizes reduce the number of buffers traversing the stack, dincreasing single stream CPU usage by up to ~30%. - Do not add HBH header to Big TCP GSO packets. This simplifies the RX path, the TX path and the NIC drivers, and is possible because user-space taps can now interpret correctly such packets without the HBH hint. - Allow IPv6 routes to be configured with a gateway address that is resolved out of a different interface than the one specified, aligning IPv6 to IPv4 behavior. - Multi-queue aware sch_cake. This makes it possible to scale the rate shaper of sch_cake across multiple CPUs, while still enforcing a single global rate on the interface. - Add support for the nbcon (new buffer console) infrastructure to netconsole, enabling lock-free, priority-based console operations that are safer in crash scenarios. - Improve the TCP ipv6 output path to cache the flow information, saving cpu cycles, reducing cache line misses and stack use. - Improve netfilter packet tracker to resolve clashes for most protocols, avoiding unneeded drops on rare occasions. - Add IP6IP6 tunneling acceleration to the flowtable infrastructure. - Reduce tcp socket size by one cache line. - Notify neighbour changes atomically, avoiding inconsistencies between the notification sequence and the actual states sequence. - Add vsock namespace support, allowing complete isolation of vsocks across different network namespaces. - Improve xsk generic performances with cache-alignment-oriented optimizations. - Support netconsole automatic target recovery, allowing netconsole to reestablish targets when underlying low-level interface comes back online. Driver API: - Support for switching the working mode (automatic vs manual) of a DPLL device via netlink. - Introduce PHY ports representation to expose multiple front-facing media ports over a single MAC. - Introduce "rx-polarity" and "tx-polarity" device tree properties, to generalize polarity inversion requirements for differential signaling. - Add helper to create, prepare and enable managed clocks. Device drivers: - Add Huawei hinic3 PF etherner driver. - Add DWMAC glue driver for Motorcomm YT6801 PCIe ethernet controller. - Add ethernet driver for MaxLinear MxL862xx switches - Remove parallel-port Ethernet driver. - Convert existing driver timestamp configuration reporting to hwtstamp_get and remove legacy ioctl(). - Convert existing drivers to .get_rx_ring_count(), simplifing the RX ring count retrieval. Also remove the legacy fallback path. - Ethernet high-speed NICs: - Broadcom (bnxt, bng): - bnxt: add FW interface update to support FEC stats histogram and NVRAM defragmentation - bng: add TSO and H/W GRO support - nVidia/Mellanox (mlx5): - improve latency of channel restart operations, reducing the used H/W resources - add TSO support for UDP over GRE over VLAN - add flow counters support for hardware steering (HWS) rules - use a static memory area to store headers for H/W GRO, leading to 12% RX tput improvement - Intel (100G, ice, idpf): - ice: reorganizes layout of Tx and Rx rings for cacheline locality and utilizes __cacheline_group* macros on the new layouts - ice: introduces Synchronous Ethernet (SyncE) support - Meta (fbnic): - adds debugfs for firmware mailbox and tx/rx rings vectors - Ethernet virtual: - geneve: introduce GRO/GSO support for double UDP encapsulation - Ethernet NICs consumer, and embedded: - Synopsys (stmmac): - some code refactoring and cleanups - RealTek (r8169): - add support for RTL8127ATF (10G Fiber SFP) - add dash and LTR support - Airoha: - AN8811HB 2.5 Gbps phy support - Freescale (fec): - add XDP zero-copy support - Thunderbolt: - add get link setting support to allow bonding - Renesas: - add support for RZ/G3L GBETH SoC - Ethernet switches: - Maxlinear: - support R(G)MII slow rate configuration - add support for Intel GSW150 - Motorcomm (yt921x): - add DCB/QoS support - TI: - icssm-prueth: support bridging (STP/RSTP) via the switchdev framework - Ethernet PHYs: - Realtek: - enable SGMII and 2500Base-X in-band auto-negotiation - simplify and reunify C22/C45 drivers - Micrel: convert bindings to DT schema - CAN: - move skb headroom content into skb extensions, making CAN metadata access more robust - CAN drivers: - rcar_canfd: - add support for FD-only mode - add support for the RZ/T2H SoC - sja1000: cleanup the CAN state handling - WiFi: - implement EPPKE/802.1X over auth frames support - split up drop reasons better, removing generic RX_DROP - additional FTM capabilities: 6 GHz support, supported number of spatial streams and supported number of LTF repetitions - better mac80211 iterators to enumerate resources - initial UHR (Wi-Fi 8) support for cfg80211/mac80211 - WiFi drivers: - Qualcomm/Atheros: - ath11k: support for Channel Frequency Response measurement - ath12k: a significant driver refactor to support multi-wiphy devices and and pave the way for future device support in the same driver (rather than splitting to ath13k) - ath12k: support for the QCC2072 chipset - Intel: - iwlwifi: partial Neighbor Awareness Networking (NAN) support - iwlwifi: initial support for U-NII-9 and IEEE 802.11bn - RealTek (rtw89): - preparations for RTL8922DE support - Bluetooth: - implement setsockopt(BT_PHY) to set the connection packet type/PHY - set link_policy on incoming ACL connections - Bluetooth drivers: - btusb: add support for MediaTek7920, Realtek RTL8761BU and 8851BE - btqca: add WCN6855 firmware priority selection feature" * tag 'net-next-7.0' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (1254 commits) bnge/bng_re: Add a new HSI net: macb: Fix tx/rx malfunction after phy link down and up af_unix: Fix memleak of newsk in unix_stream_connect(). net: ti: icssg-prueth: Add optional dependency on HSR net: dsa: add basic initial driver for MxL862xx switches net: mdio: add unlocked mdiodev C45 bus accessors net: dsa: add tag format for MxL862xx switches dt-bindings: net: dsa: add MaxLinear MxL862xx selftests: drivers: net: hw: Modify toeplitz.c to poll for packets octeontx2-pf: Unregister devlink on probe failure net: renesas: rswitch: fix forwarding offload statemachine ionic: Rate limit unknown xcvr type messages tcp: inet6_csk_xmit() optimization tcp: populate inet->cork.fl.u.ip6 in tcp_v6_syn_recv_sock() tcp: populate inet->cork.fl.u.ip6 in tcp_v6_connect() ipv6: inet6_csk_xmit() and inet6_csk_update_pmtu() use inet->cork.fl.u.ip6 ipv6: use inet->cork.fl.u.ip6 and np->final in ip6_datagram_dst_update() ipv6: use np->final in inet6_sk_rebuild_header() ipv6: add daddr/final storage in struct ipv6_pinfo net: stmmac: qcom-ethqos: fix qcom_ethqos_serdes_powerup() ...
2026-02-10Merge tag 'irq-cleanups-2026-02-09' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip Pull irq cleanups from Thomas Gleixner: "A series of treewide cleanups to ensure interrupt request consistency. - Add the missing IRQF_COND_ONESHOT flag to devm_request_irq() This is inconsistent vs request_irq() and causes the same issues which where addressed with the introduction of this flag - Cleanup IRQF_ONESHOT and IRQF_NO_THREAD usage Quite some drivers have inconsistent interrupt request flags related to interrupt threading namely IRQF_ONESHOT and IRQF_NO_THREAD. This leads to warnings and/or malfunction when forced interrupt threading is enabled. - Remove stub primary (hard interrupt) handlers A bunch of drivers implement a stub primary (hard interrupt) handler which just returns IRQ_WAKE_THREAD. The same functionality is provided by the core code when the primary handler argument of request_thread_irq() is set to NULL" * tag 'irq-cleanups-2026-02-09' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: media: pci: mg4b: Use IRQF_NO_THREAD mfd: wm8350-core: Use IRQF_ONESHOT thermal/qcom/lmh: Replace IRQF_ONESHOT with IRQF_NO_THREAD rtc: amlogic-a4: Remove IRQF_ONESHOT usb: typec: fusb302: Remove IRQF_ONESHOT EDAC/altera: Remove IRQF_ONESHOT char: tpm: cr50: Remove IRQF_ONESHOT ARM: versatile: Remove IRQF_ONESHOT scsi: efct: Use IRQF_ONESHOT and default primary handler Bluetooth: btintel_pcie: Use IRQF_ONESHOT and default primary handler bus: fsl-mc: Use default primary handler mailbox: bcm-ferxrm-mailbox: Use default primary handler iommu/amd: Use core's primary handler and set IRQF_ONESHOT platform/x86: int0002: Remove IRQF_ONESHOT from request_irq() genirq: Set IRQF_COND_ONESHOT in devm_request_irq().
2026-02-01Bluetooth: btintel_pcie: Use IRQF_ONESHOT and default primary handlerSebastian Andrzej Siewior
There is no added value in btintel_pcie_msix_isr() compared to irq_default_primary_handler(). Using a threaded interrupt without a dedicated primary handler mandates the IRQF_ONESHOT flag to mask the interrupt source while the threaded handler is active. Otherwise the interrupt can fire again before the threaded handler had a chance to run. Use the default primary interrupt handler by specifying NULL and set IRQF_ONESHOT so the interrupt source is masked until the secondary handler is done. Fixes: c2b636b3f788d ("Bluetooth: btintel_pcie: Add support for PCIe transport") Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Thomas Gleixner <tglx@kernel.org> Link: https://patch.msgid.link/20260128095540.863589-7-bigeasy@linutronix.de
2026-01-29Bluetooth: hci_qca: Enable HFP hardware offload for WCN6855 and WCN7850Mengshi Wu
Add QCA_CAP_HFP_HW_OFFLOAD capability flag to WCN6855 and WCN7850 device data structures to enable Hands-Free Profile (HFP) hardware offload support on these Qualcomm Bluetooth chipsets. Signed-off-by: Mengshi Wu <mengshi.wu@oss.qualcomm.com> Acked-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2026-01-29Bluetooth: hci_qca: Refactor HFP hardware offload capability handlingMengshi Wu
Replace SoC-specific check with capability-based approach for HFP hardware offload configuration. Add QCA_CAP_HFP_HW_OFFLOAD capability flag and support_hfp_hw_offload field to qca_serdev structure. Add QCA_CAP_HFP_HW_OFFLOAD capability flag to QCA2066 device data structures. Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com> Signed-off-by: Mengshi Wu <mengshi.wu@oss.qualcomm.com> Acked-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2026-01-29Bluetooth: btusb: Add USB ID 7392:e611 for Edimax EW-7611UXBZenm Chen
Add USB ID 7392:e611 for Edimax EW-7611UXB which is RTL8851BU-based Wi-Fi + Bluetooth adapter. The information in /sys/kernel/debug/usb/devices about the Bluetooth device is listed as the below: T: Bus=03 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#= 6 Spd=480 MxCh= 0 D: Ver= 2.00 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=7392 ProdID=e611 Rev= 0.00 S: Manufacturer=Realtek S: Product=802.11ax WLAN Adapter S: SerialNumber=00e04c000001 C:* #Ifs= 3 Cfg#= 1 Atr=e0 MxPwr=500mA A: FirstIf#= 0 IfCount= 2 Cls=e0(wlcon) Sub=01 Prot=01 I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms I: If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 63 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 63 Ivl=1ms I:* If#= 2 Alt= 0 #EPs= 8 Cls=ff(vend.) Sub=ff Prot=ff Driver=rtw89_8851bu_git E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=06(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=07(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=09(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=0a(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=0b(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=0c(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms Cc: stable@vger.kernel.org # 6.6.x Signed-off-by: Zenm Chen <zenmchen@gmail.com> Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2026-01-29Bluetooth: hci_uart: fix null-ptr-deref in hci_uart_write_workJia-Hong Su
hci_uart_set_proto() sets HCI_UART_PROTO_INIT before calling hci_uart_register_dev(), which calls proto->open() to initialize hu->priv. However, if a TTY write wakeup occurs during this window, hci_uart_tx_wakeup() may schedule write_work before hu->priv is initialized, leading to a NULL pointer dereference in hci_uart_write_work() when proto->dequeue() accesses hu->priv. The race condition is: CPU0 CPU1 ---- ---- hci_uart_set_proto() set_bit(HCI_UART_PROTO_INIT) hci_uart_register_dev() tty write wakeup hci_uart_tty_wakeup() hci_uart_tx_wakeup() schedule_work(&hu->write_work) proto->open(hu) // initializes hu->priv hci_uart_write_work() hci_uart_dequeue() proto->dequeue(hu) // accesses hu->priv (NULL!) Fix this by moving set_bit(HCI_UART_PROTO_INIT) after proto->open() succeeds, ensuring hu->priv is initialized before any work can be scheduled. Fixes: 5df5dafc171b ("Bluetooth: hci_uart: Fix another race during initialization") Link: https://lore.kernel.org/linux-bluetooth/6969764f.170a0220.2b9fc4.35a7@mx.google.com/ Signed-off-by: Jia-Hong Su <s11242586@gmail.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2026-01-29Bluetooth: btusb: Remove duplicate entry for 0x13d3/0x3618Linmao Li
The USB device ID 0x13d3/0x3618 is listed twice in the device table. Remove the duplicate entry and keep the one under the correct "Realtek 8852BT/8852BE-VT Bluetooth devices" section. Signed-off-by: Linmao Li <lilinmao@kylinos.cn> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2026-01-29Bluetooth: btusb: Add device ID for Realtek RTL8761BUJacopo Scannella
Add USB device ID 0x2c0a:0x8761 to the btusb driver fo the Realtek RTL8761BU Bluetooth adapter. Reference: https://www.startech.com/en-us/networking-io/av53c1-usb-bluetooth Signed-off-by: Jacopo Scannella <code@charlie.cat> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2026-01-29Bluetooth: btintel: Remove unneeded CONFIG_PM* #ifdef'sBastien Nocera
The functions are already disabled if CONFIG_PM or CONFIG_PM_SLEEP are disabled through the use of SET_SYSTEM_SLEEP_PM_OPS() and SET_RUNTIME_PM_OPS(). This increases build coverage and allows to drop a few #ifdef's. Signed-off-by: Bastien Nocera <hadess@hadess.net> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2026-01-29Bluetooth: btnxpuart: Remove unneeded CONFIG_PM ifdefBastien Nocera
The functions are already disabled through the use of pm_ptr() when CONFIG_PM is disabled, and will be removed from the final linked code as not needed. This increases build coverage and allows to drop an #ifdef. Signed-off-by: Bastien Nocera <hadess@hadess.net> Reviewed-by: Neeraj Sanjay Kale <neeraj.sanjaykale@nxp.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2026-01-29Bluetooth: btusb: Add new VID/PID for RTL8852CEShell Chen
Add VID:PID 13d3:3612 to the quirks_table. This ID pair is found in the Realtek RTL8852CE PCIe module in an ASUS TUF A14 2025 (FA401KM) laptop. Tested on aforementioned laptop. The device info from /sys/kernel/debug/usb/devices is listed as below. T: Bus=03 Lev=01 Prnt=01 Port=04 Cnt=01 Dev#= 2 Spd=12 MxCh= 0 D: Ver= 1.00 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=13d3 ProdID=3612 Rev= 0.00 S: Manufacturer=Realtek S: Product=Bluetooth Radio S: SerialNumber=00e04c000001 C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=500mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms I: If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 63 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 63 Ivl=1ms Signed-off-by: Shell Chen <w27@sorz.org> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2026-01-29Bluetooth: btintel_pcie: Remove unnecessary check before kfree_skb()Chen Ni
The kfree_skb() function internally checks if the skb is NULL, so an explicit check before calling it is redundant and can be removed. Signed-off-by: Chen Ni <nichen@iscas.ac.cn> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2026-01-29Bluetooth: btusb: Reject autosuspend if discovery is activeLinmao Li
If USB autosuspend occurs while discovery is active, the ongoing HCI operation may not complete successfully. On some devices, this can leave discovery.state stuck in DISCOVERY_FINDING. Signed-off-by: Linmao Li <lilinmao@kylinos.cn> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2026-01-29Bluetooth: btusb: Use pm_ptr instead of #ifdef CONFIG_PMBastien Nocera
This increases build coverage and allows to drop an #ifdef. Signed-off-by: Bastien Nocera <hadess@hadess.net> Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2026-01-29Bluetooth: btusb: Add USB ID 0489:e112 for Realtek 8851BETechie Ernie
Add USB ID 0489:e112 for the Realtek 8851BE Bluetooth adapter. Without this entry, the device is not handled correctly by btusb and Bluetooth fails to initialise. Adding the ID enables proper Realtek initialization for Bluetooth to work on various motherboards using this Bluetooth adapter. The device identifies as: Bus 001 Device XXX: ID 0489:e112 Foxconn / Hon Hai Bluetooth Radio Tested on Realtek 8851BE. Bluetooth works after this change is made. Signed-off-by: Techie Ernie <techieernie@gmail.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2026-01-29Bluetooth: btqca: Add WCN6855 firmware priority selection featureShuai Zhang
Historically, WCN685x and QCA2066 shared the same firmware files. Now, changes are planned for the firmware that will make it incompatible with QCA2066, so a new firmware name is required for WCN685x. Test Steps: - Boot device - Check the BTFW loading status via dmesg Sanity pass and Test Log: QCA Downloading qca/wcnhpbftfw21.tlv Direct firmware load for qca/wcnhpbftfw21.tlv failed with error -2 QCA Downloading qca/hpbftfw21.tlv Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com> Signed-off-by: Shuai Zhang <shuai.zhang@oss.qualcomm.com> Acked-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2026-01-29Bluetooth: btqca: move WCN7850 workaround to the callerShuai Zhang
WCN7850 will first attempt to use ELF_TYPE_PATCH, and if that fails, it will fall back to TLV_TYPE_PATCH. To code uniformity, move WCN7850 workaround to the caller. Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com> Signed-off-by: Shuai Zhang <shuai.zhang@oss.qualcomm.com> Acked-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2026-01-29Bluetooth: btmtksdio: Use pm_ptr instead of #ifdef CONFIG_PMUwe Kleine-König
This increases build coverage and allows to drop an #ifdef. Signed-off-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2026-01-29Bluetooth: hci_bcm4377: Use generic power managementVaibhav Gupta
Switch to the generic PCI power management framework and remove legacy callbacks like .suspend() and .resume(). With the generic framework, the standard PCI related work like: - pci_save/restore_state() - pci_enable/disable_device() - pci_set_power_state() is handled by the PCI core and this driver should implement only hci_bcm4377 specific operations in its respective callback functions. Signed-off-by: Vaibhav Gupta <vaibhavgupta40@gmail.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2026-01-29Bluetooth: btusb: Add support for MediaTek7920 0489:e158Bluecross
Add support for MediaTek7920 0489:e158 /sys/kernel/debug/usb/devices reports for that device: T: Bus=03 Lev=01 Prnt=01 Port=02 Cnt=03 Dev#= 5 Spd=480 MxCh= 0 D: Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=0489 ProdID=e158 Rev= 1.00 S: Manufacturer=MediaTek Inc. S: Product=Wireless_Device S: SerialNumber=000000000 C:* #Ifs= 3 Cfg#= 1 Atr=e0 MxPwr=100mA A: FirstIf#= 0 IfCount= 3 Cls=e0(wlcon) Sub=01 Prot=01 I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=125us E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms I: If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 63 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 63 Ivl=1ms I:* If#= 2 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none) E: Ad=8a(I) Atr=03(Int.) MxPS= 64 Ivl=125us E: Ad=0a(O) Atr=03(Int.) MxPS= 64 Ivl=125us I: If#= 2 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none) E: Ad=8a(I) Atr=03(Int.) MxPS= 512 Ivl=125us E: Ad=0a(O) Atr=03(Int.) MxPS= 512 Ivl=125us Signed-off-by: Andrew Elatsev <elantsew.andrew@gmail.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2026-01-29Bluetooth: hci_qca: Fix SSR (SubSystem Restart) fail when BT_EN is pulled up ↵Shuai Zhang
by hw On QCS9075 and QCA8275 platforms, the BT_EN pin is always pulled up by hw and cannot be controlled by the host. As a result, in case of a firmware crash, the host cannot trigger a cold reset. Instead, the BT controller performs a warm restart on its own, without reloading the firmware. This leads to the controller remaining in IBS_WAKE state, while the host expects it to be in sleep mode. The mismatch causes HCI reset commands to time out. Additionally, the driver does not clear internal flags QCA_SSR_TRIGGERED and QCA_IBS_DISABLED, which blocks the reset sequence. If the SSR duration exceeds 2 seconds, the host may enter TX sleep mode due to tx_idle_timeout, further preventing recovery. Also, memcoredump_flag is not cleared, so only the first SSR generates a coredump. Tell the driver that the BT controller has undergone a proper restart sequence: - Clear QCA_SSR_TRIGGERED and QCA_IBS_DISABLED flags after SSR. - Add a 50ms delay to allow the controller to complete its warm reset. - Reset tx_idle_timer to prevent the host from entering TX sleep mode. - Clear memcoredump_flag to allow multiple coredump captures. Apply these steps only when HCI_QUIRK_NON_PERSISTENT_SETUP is not set, which indicates that BT_EN is defined in DTS and cannot be toggled. Refer to the comment in include/net/bluetooth/hci.h for details on HCI_QUIRK_NON_PERSISTENT_SETUP. Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com> Signed-off-by: Shuai Zhang <shuai.zhang@oss.qualcomm.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2026-01-22Bluetooth: hci_uart: fix null-ptr-deref in hci_uart_write_workJia-Hong Su
hci_uart_set_proto() sets HCI_UART_PROTO_INIT before calling hci_uart_register_dev(), which calls proto->open() to initialize hu->priv. However, if a TTY write wakeup occurs during this window, hci_uart_tx_wakeup() may schedule write_work before hu->priv is initialized, leading to a NULL pointer dereference in hci_uart_write_work() when proto->dequeue() accesses hu->priv. The race condition is: CPU0 CPU1 ---- ---- hci_uart_set_proto() set_bit(HCI_UART_PROTO_INIT) hci_uart_register_dev() tty write wakeup hci_uart_tty_wakeup() hci_uart_tx_wakeup() schedule_work(&hu->write_work) proto->open(hu) // initializes hu->priv hci_uart_write_work() hci_uart_dequeue() proto->dequeue(hu) // accesses hu->priv (NULL!) Fix this by moving set_bit(HCI_UART_PROTO_INIT) after proto->open() succeeds, ensuring hu->priv is initialized before any work can be scheduled. Fixes: 5df5dafc171b ("Bluetooth: hci_uart: Fix another race during initialization") Link: https://lore.kernel.org/linux-bluetooth/6969764f.170a0220.2b9fc4.35a7@mx.google.com/ Signed-off-by: Jia-Hong Su <s11242586@gmail.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2025-12-19Bluetooth: btusb: revert use of devm_kzalloc in btusbRaphael Pinsonneault-Thibeault
This reverts commit 98921dbd00c4e ("Bluetooth: Use devm_kzalloc in btusb.c file"). In btusb_probe(), we use devm_kzalloc() to allocate the btusb data. This ties the lifetime of all the btusb data to the binding of a driver to one interface, INTF. In a driver that binds to other interfaces, ISOC and DIAG, this is an accident waiting to happen. The issue is revealed in btusb_disconnect(), where calling usb_driver_release_interface(&btusb_driver, data->intf) will have devm free the data that is also being used by the other interfaces of the driver that may not be released yet. To fix this, revert the use of devm and go back to freeing memory explicitly. Fixes: 98921dbd00c4e ("Bluetooth: Use devm_kzalloc in btusb.c file") Signed-off-by: Raphael Pinsonneault-Thibeault <rpthibeault@gmail.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2025-12-17Bluetooth: hci_qca: Migrate to serdev specific shutdown functionUwe Kleine-König
This saves a cast in the driver. The motivation is stop using the callback .shutdown in qca_serdev_driver.driver to make it possible to drop that. Signed-off-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com> Link: https://patch.msgid.link/261a3384e25c4837d4efee87958805f15d7d4e3c.1765526117.git.u.kleine-koenig@baylibre.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2025-12-17Bluetooth: hci_aml: Migrate to serdev specific shutdown functionUwe Kleine-König
This saves a cast in the driver. The motivation is stop using the callback .shutdown in qca_serdev_driver.driver to make it possible to drop that. Signed-off-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com> Link: https://patch.msgid.link/42ae20ba70ff6fbbbd9b846ac9acd0f7d58451b0.1765526117.git.u.kleine-koenig@baylibre.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2025-12-01Bluetooth: btusb: Add new VID/PID 13d3/3533 for RTL8821CEGongwei Li
Add VID 13d3 & PID 3533 for Realtek RTL8821CE USB Bluetooth chip. The information in /sys/kernel/debug/usb/devices about the Bluetooth device is listed as the below. T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=12 MxCh= 0 D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=13d3 ProdID=3533 Rev= 1.10 S: Manufacturer=Realtek S: Product=Bluetooth Radio S: SerialNumber=00e04c000001 C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=500mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms Signed-off-by: Gongwei Li <ligongwei@kylinos.cn> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2025-12-01drivers/bluetooth: btbcm: Use kmalloc_array() to prevent overflowAyaan Mirza Baig
Replace the open-coded multiplication in kmalloc() with a call to kmalloc_array() to prevent potential integer overflows. This is a mechanical change, replacing BCM_FW_NAME_LEN with the type-safe sizeof(*fw_name) as the element size Signed-off-by: Ayaan Mirza Baig <ayaanmirzabaig85@gmail.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2025-12-01Bluetooth: btintel_pcie: Introduce HCI Driver protocolChethan T N
This patch adds the infrastructure that allow the user space program to talk to intel pcie driver directly for fetching basic driver details. The changes introduced are referred form commit 04425292a62c15 ("Bluetooth: Introduce HCI Driver protocol") Signed-off-by: Chethan T N <chethan.tumkur.narayan@intel.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2025-12-01Bluetooth: btusb: add new custom firmwaresShuai Zhang
The new platform uses the QCA2066 chip along with a new board ID, which requires a dedicated firmware file to ensure proper initialization. Without this entry, the driver cannot locate and load the correct firmware, resulting in Bluetooth bring-up failure. This patch adds a new entry to the firmware table for QCA2066 so that the driver can correctly identify the board ID and load the appropriate firmware from 'qca/QCA2066/' in the linux-firmware repository. Signed-off-by: Shuai Zhang <quic_shuaz@quicinc.com> Acked-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2025-12-01Bluetooth: btusb: Add new VID/PID 0x13d3/0x3619 for RTL8852BE-VTMax Chou
Add the support ID(0x13d3, 0x3619) to usb_device_id table for Realtek RTL8852BE-VT. The device info from /sys/kernel/debug/usb/devices as below. T: Bus=04 Lev=02 Prnt=02 Port=05 Cnt=01 Dev#= 86 Spd=12 MxCh= 0 D: Ver= 1.00 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=13d3 ProdID=3619 Rev= 0.00 S: Manufacturer=Realtek S: Product=Bluetooth Radio S: SerialNumber=00e04c000001 C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=500mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms Signed-off-by: Max Chou <max.chou@realtek.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2025-12-01Bluetooth: btusb: Add new VID/PID 0x13d3/0x3618 for RTL8852BE-VTMax Chou
Add the support ID(0x13d3, 0x3618) to usb_device_id table for Realtek RTL8852BE-VT. The device info from /sys/kernel/debug/usb/devices as below. T: Bus=04 Lev=02 Prnt=02 Port=05 Cnt=01 Dev#= 86 Spd=12 MxCh= 0 D: Ver= 1.00 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=13d3 ProdID=3618 Rev= 0.00 S: Manufacturer=Realtek S: Product=Bluetooth Radio S: SerialNumber=00e04c000001 C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=500mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms Signed-off-by: Max Chou <max.chou@realtek.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2025-12-01Bluetooth: btusb: Add new VID/PID 0x0489/0xE12F for RTL8852BE-VTMax Chou
Add the support ID(0x0489, 0xE12F) to usb_device_id table for Realtek RTL8852BE-VT. The device info from /sys/kernel/debug/usb/devices as below. T: Bus=04 Lev=02 Prnt=02 Port=05 Cnt=01 Dev#= 86 Spd=12 MxCh= 0 D: Ver= 1.00 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=0489 ProdID=e12f Rev= 0.00 S: Manufacturer=Realtek S: Product=Bluetooth Radio S: SerialNumber=00e04c000001 C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=500mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms Signed-off-by: Max Chou <max.chou@realtek.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2025-12-01Bluetooth: btrtl: Add the support for RTL8761CUVMax Chou
Add support for RTL8761CUV BT controller on the USB interface. Do not apply IC_MATCH_FL_HCIVER when hci_ver is 0 in the ic_id_table. The device info from /sys/kernel/debug/usb/devices as below. T: Bus=02 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 13 Spd=12 MxCh= 0 D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=0bda ProdID=c761 Rev= 2.00 S: Manufacturer=Realtek S: Product=Bluetooth Controller S: SerialNumber=10000 C:* #Ifs= 2 Cfg#= 1 Atr=a0 MxPwr=100mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 64 Ivl=1ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms I: If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 63 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 63 Ivl=1ms Signed-off-by: Max Chou <max.chou@realtek.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2025-12-01Bluetooth: Remove redundant pm_runtime_mark_last_busy() callsSakari Ailus
pm_runtime_put_autosuspend(), pm_runtime_put_sync_autosuspend(), pm_runtime_autosuspend() and pm_request_autosuspend() now include a call to pm_runtime_mark_last_busy(). Remove the now-reduntant explicit call to pm_runtime_mark_last_busy(). Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2025-12-01Bluetooth: btusb: Reclassify Qualcomm WCN6855 debug packetsPascal Giard
Some Qualcomm Bluetooth controllers, e.g., QCNFA765 with WCN6855 chip, send debug packets as ACL frames with header 0x2EDC. The kernel misinterprets these as malformed ACL packets, causing repeated errors: Bluetooth: hci0: ACL packet for unknown connection handle 3804 This can occur hundreds of times per minute, greatly cluttering logs. On my computer, I am observing approximately 7 messages per second when streaming audio to a speaker. For Qualcomm controllers exchanging over UART, hci_qca.c already filters out these debug packets. This patch is for controllers not going through UART, but USB. This patch uses the classify_pkt_type callback to reclassify the packets with handle 0x2EDC as HCI_DIAG_PKT before they reach the HCI layer. This change is only applied to Qualcomm devices marked as BTUSB_QCA_WCN6855. Tested on: Thinkpad T14 gen2 (AMD) with QCNFA765 (0489:E0D0) Signed-off-by: Pascal Giard <pascal.giard@etsmtl.ca> Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2025-12-01Bluetooth: btusb: Add new VID/PID 2b89/6275 for RTL8761BUVChingbin Li
Add VID 2b89 & PID 6275 for Realtek RTL8761BUV USB Bluetooth chip. The information in /sys/kernel/debug/usb/devices about the Bluetooth device is listed as the below. T: Bus=01 Lev=01 Prnt=01 Port=02 Cnt=01 Dev#= 6 Spd=12 MxCh= 0 D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=2b89 ProdID=6275 Rev= 2.00 S: Manufacturer=Realtek S: Product=Bluetooth Radio S: SerialNumber=00E04C239987 C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=500mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms Signed-off-by: Chingbin Li <liqb365@163.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2025-12-01Bluetooth: btintel_pcie: Suspend/Resume: Controller doorbell interrupt handlingRavindra
Due to a hardware bug during suspend/resume, the controller may miss a doorbell interrupt. To address this, a retry mechanism has been added to inform the controller before reporting a failure. Test case: - run suspend and resume cycles. Signed-off-by: Ravindra <ravindra@intel.com> Signed-off-by: Kiran K <kiran.k@intel.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2025-12-01Bluetooth: btintel_pcie: Support for S4 (Hibernate)Ravindra
During S4 (hibernate), the Bluetooth device loses power. Upon resume, the driver performs the following actions: 1. Unregisters hdev 2. Calls function level reset 3. Registers hdev Test case: - run command sudo rtcwake -m disk -s 60 Signed-off-by: Ravindra <ravindra@intel.com> Signed-off-by: Kiran K <kiran.k@intel.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2025-12-01Bluetooth: btusb: MT7922: Add VID/PID 0489/e170Chris Lu
Add VID 0489 & PID e170 for MediaTek MT7922 USB Bluetooth chip. The information in /sys/kernel/debug/usb/devices about the Bluetooth device is listed as the below. T: Bus=06 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=480 MxCh= 0 D: Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=0489 ProdID=e170 Rev= 1.00 S: Manufacturer=MediaTek Inc. S: Product=Wireless_Device S: SerialNumber=000000000 C:* #Ifs= 3 Cfg#= 1 Atr=e0 MxPwr=100mA A: FirstIf#= 0 IfCount= 3 Cls=e0(wlcon) Sub=01 Prot=01 I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=125us E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms I: If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 63 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 63 Ivl=1ms I:* If#= 2 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none) E: Ad=8a(I) Atr=03(Int.) MxPS= 64 Ivl=125us E: Ad=0a(O) Atr=03(Int.) MxPS= 64 Ivl=125us I: If#= 2 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none) E: Ad=8a(I) Atr=03(Int.) MxPS= 512 Ivl=125us E: Ad=0a(O) Atr=03(Int.) MxPS= 512 Ivl=125us Signed-off-by: Chris Lu <chris.lu@mediatek.com> Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2025-12-01Bluetooth: btusb: MT7920: Add VID/PID 0489/e135Chris Lu
Add VID 0489 & PID e135 for MediaTek MT7920 USB Bluetooth chip. The information in /sys/kernel/debug/usb/devices about the Bluetooth device is listed as the below. T: Bus=06 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=480 MxCh= 0 D: Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=0489 ProdID=e135 Rev= 1.00 S: Manufacturer=MediaTek Inc. S: Product=Wireless_Device S: SerialNumber=000000000 C:* #Ifs= 3 Cfg#= 1 Atr=e0 MxPwr=100mA A: FirstIf#= 0 IfCount= 3 Cls=e0(wlcon) Sub=01 Prot=01 I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=125us E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms I: If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 63 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 63 Ivl=1ms I:* If#= 2 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none) E: Ad=8a(I) Atr=03(Int.) MxPS= 64 Ivl=125us E: Ad=0a(O) Atr=03(Int.) MxPS= 64 Ivl=125us I: If#= 2 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none) E: Ad=8a(I) Atr=03(Int.) MxPS= 64 Ivl=125us E: Ad=0a(O) Atr=03(Int.) MxPS= 64 Ivl=125us Signed-off-by: Chris Lu <chris.lu@mediatek.com> Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
generated by cgit v1.2.3 (git 2.46.0) at 2026-04-03 22:54:25 +0000