| Age | Commit message (Collapse) | Author |
|---|
|
clang is not inlining skb_frag_unref() and __skb_frag_unref()
in gro fast path.
It also does not inline gro_try_pull_from_frag0().
Using __always_inline fixes this issue, makes the
kernel faster _and_ smaller.
Also change __skb_frag_ref(), skb_frag_ref() and skb_page_unref()
to let them inlined for the last patch in this series.
$ scripts/bloat-o-meter -t vmlinux.0 vmlinux.1
add/remove: 2/6 grow/shrink: 1/2 up/down: 218/-511 (-293)
Function old new delta
gro_pull_from_frag0 - 188 +188
__pfx_gro_pull_from_frag0 - 16 +16
skb_shift 1125 1139 +14
__pfx_skb_frag_unref 16 - -16
__pfx_gro_try_pull_from_frag0 16 - -16
__pfx___skb_frag_unref 16 - -16
__skb_frag_unref 36 - -36
skb_frag_unref 59 - -59
dev_gro_receive 1608 1514 -94
napi_gro_frags 892 771 -121
gro_try_pull_from_frag0 153 - -153
Total: Before=22566192, After=22565899, chg -0.00%
Signed-off-by: Eric Dumazet <edumazet@google.com>
Link: https://patch.msgid.link/20260122045720.1221017-2-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The following (anti-)pattern was observed in the code tree:
do {
start = u64_stats_fetch_begin(&pstats->syncp);
memcpy(&temp, &pstats->stats, sizeof(temp));
} while (u64_stats_fetch_retry(&pstats->syncp, start));
On 64bit arches, struct u64_stats_sync is empty and provides no help
against load/store tearing, especially for memcpy(), for which arches may
provide their highly-optimized implements.
In theory the affected code should convert to u64_stats_t, or use
READ_ONCE()/WRITE_ONCE() properly.
However since there are needs to copy chunks of statistics, instead of
writing loops at random places, we provide a safe memcpy() variant for
u64_stats.
Signed-off-by: David Yang <mmyangfl@gmail.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Link: https://patch.msgid.link/20260120092137.2161162-2-mmyangfl@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc/iio driver fixes from Greg KH:
"Here are some small char/misc/iio and some other minor driver
subsystem fixes for 6.19-rc7. Nothing huge here, just some fixes for
reported issues including:
- lots of little iio driver fixes
- comedi driver fixes
- mux driver fix
- w1 driver fixes
- uio driver fix
- slimbus driver fixes
- hwtracing bugfix
- other tiny bugfixes
All of these have been in linux-next for a while with no reported
issues"
* tag 'char-misc-6.19-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (36 commits)
comedi: dmm32at: serialize use of paged registers
mei: trace: treat reg parameter as string
uio: pci_sva: correct '-ENODEV' check logic
uacce: ensure safe queue release with state management
uacce: implement mremap in uacce_vm_ops to return -EPERM
uacce: fix isolate sysfs check condition
uacce: fix cdev handling in the cleanup path
slimbus: core: clean up of_slim_get_device()
slimbus: core: fix of_slim_get_device() kernel doc
slimbus: core: amend slim_get_device() kernel doc
slimbus: core: fix device reference leak on report present
slimbus: core: fix runtime PM imbalance on report present
slimbus: core: fix OF node leak on registration failure
intel_th: rename error label
intel_th: fix device leak on output open()
comedi: Fix getting range information for subdevices 16 to 255
mux: mmio: Fix IS_ERR() vs NULL check in probe()
interconnect: debugfs: initialize src_node and dst_node to empty strings
iio: dac: ad3552r-hs: fix out-of-bound write in ad3552r_hs_write_data_source
iio: accel: iis328dq: fix gain values
...
|
|
Implement session cookie for fsession. The session cookies will be stored
in the stack, and the layout of the stack will look like this:
return value -> 8 bytes
argN -> 8 bytes
...
arg1 -> 8 bytes
nr_args -> 8 bytes
ip (optional) -> 8 bytes
cookie2 -> 8 bytes
cookie1 -> 8 bytes
The offset of the cookie for the current bpf program, which is in 8-byte
units, is stored in the
"(((u64 *)ctx)[-1] >> BPF_TRAMP_COOKIE_INDEX_SHIFT) & 0xFF". Therefore, we
can get the session cookie with ((u64 *)ctx)[-offset].
Implement and inline the bpf_session_cookie() for the fsession in the
verifier.
Signed-off-by: Menglong Dong <dongml2@chinatelecom.cn>
Link: https://lore.kernel.org/r/20260124062008.8657-6-dongml2@chinatelecom.cn
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
If fsession exists, we will use the bit (1 << BPF_TRAMP_IS_RETURN_SHIFT)
in ((u64 *)ctx)[-1] to store the "is_return" flag.
The logic of bpf_session_is_return() for fsession is implemented in the
verifier by inline following code:
bool bpf_session_is_return(void *ctx)
{
return (((u64 *)ctx)[-1] >> BPF_TRAMP_IS_RETURN_SHIFT) & 1;
}
Signed-off-by: Menglong Dong <dongml2@chinatelecom.cn>
Co-developed-by: Leon Hwang <leon.hwang@linux.dev>
Signed-off-by: Leon Hwang <leon.hwang@linux.dev>
Link: https://lore.kernel.org/r/20260124062008.8657-5-dongml2@chinatelecom.cn
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
The fsession is something that similar to kprobe session. It allow to
attach a single BPF program to both the entry and the exit of the target
functions.
Introduce the struct bpf_fsession_link, which allows to add the link to
both the fentry and fexit progs_hlist of the trampoline.
Signed-off-by: Menglong Dong <dongml2@chinatelecom.cn>
Co-developed-by: Leon Hwang <leon.hwang@linux.dev>
Signed-off-by: Leon Hwang <leon.hwang@linux.dev>
Link: https://lore.kernel.org/r/20260124062008.8657-2-dongml2@chinatelecom.cn
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/driver-core/driver-core
Pull driver core fixes from Danilo Krummrich:
- Always inline I/O and IRQ methods using build_assert!() to avoid
false positive build errors
- Do not free the driver's device private data in I2C shutdown()
avoiding race conditions that can lead to UAF bugs
- Drop the driver's device private data after the driver has been
fully unbound from its device to avoid UAF bugs from &Device<Bound>
scopes, such as IRQ callbacks
* tag 'driver-core-6.19-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/driver-core/driver-core:
rust: driver: drop device private data post unbind
rust: driver: add DriverData type to the DriverLayout trait
rust: driver: add DEVICE_DRIVER_OFFSET to the DriverLayout trait
rust: driver: introduce a DriverLayout trait
rust: auxiliary: add Driver::unbind() callback
rust: i2c: do not drop device private data on shutdown()
rust: irq: always inline functions using build_assert with arguments
rust: io: always inline functions using build_assert with arguments
|
|
In clang version 21.1 and later the -Wimplicit-enum-enum-cast warning
option has been introduced. This warning is enabled by default and can
be used to catch .queuecommand() implementations that return another
value than 0 or one of the SCSI_MLQUEUE_* constants. Hence this patch
that changes the return type of the .queuecommand() implementations from
'int' into 'enum scsi_qc_status'. No functionality has been changed.
Cc: Damien Le Moal <dlemoal@kernel.org>
Cc: John Garry <john.g.garry@oracle.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Link: https://patch.msgid.link/20260115210357.2501991-6-bvanassche@acm.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Merge in patches to support several patch series such as Soft Reserve
handling, type2 accelerator enabling, and LSA 2.1 labeling support.
Mainly addition of cxl_memdev_attach() to allow the memdev probe
to make a decision of proceed/fail depending success of CXL topology
enumeration.
dax/hmem, e820, resource: Defer Soft Reserved insertion until hmem is ready
cxl/mem: Introduce cxl_memdev_attach for CXL-dependent operation
cxl/mem: Drop @host argument to devm_cxl_add_memdev()
cxl/mem: Convert devm_cxl_add_memdev() to scope-based-cleanup
cxl/port: Arrange for always synchronous endpoint attach
cxl/mem: Arrange for always-synchronous memdev attach
cxl/mem: Fix devm_cxl_memdev_edac_release() confusion
|
|
Some/most devices implementing gso_partial need to disable the GSO partial
features when the IP ID can't be mangled; to that extend each of them
implements something alike the following[1]:
if (skb->encapsulation && !(features & NETIF_F_TSO_MANGLEID))
features &= ~NETIF_F_TSO;
in the ndo_features_check() op, which leads to a bit of duplicate code.
Later patch in the series will implement GSO partial support for virtual
devices, and the current status quo will require more duplicate code and
a new indirect call in the TX path for them.
Introduce the mangleid_features mask, allowing the core to disable NIC
features based on/requiring MANGLEID, without any further intervention
from the driver.
The same functionality could be alternatively implemented adding a single
boolean flag to the struct net_device, but would require an additional
checks in ndo_features_check().
Also note that [1] is incorrect if the NIC additionally implements
NETIF_F_GSO_UDP_L4, mangleid_features transparently handle even such a
case.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://patch.msgid.link/5a7cdaeea40b0a29b88e525b6c942d73ed3b8ce7.1769011015.git.pabeni@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
On the embedded platform, certain critical data, such as IMU data, is
transmitted through UART. The tty_flip_buffer_push() interface in the TTY
layer uses system_dfl_wq to handle the flipping of the TTY buffer.
Although the unbound workqueue can create new threads on demand and wake
up the kworker thread on an idle CPU, it may be preempted by real-time
tasks or other high-prio tasks.
flush_to_ldisc() needs to wake up the relevant data handle thread. When
executing __wake_up_common_lock(), it calls spin_lock_irqsave(), which
does not disable preemption but disables migration in RT-Linux. This
prevents the kworker thread from being migrated to other cores by CPU's
balancing logic, resulting in long delays. The call trace is as follows:
__wake_up_common_lock
__wake_up
ep_poll_callback
__wake_up_common
__wake_up_common_lock
__wake_up
n_tty_receive_buf_common
n_tty_receive_buf2
tty_ldisc_receive_buf
tty_port_default_receive_buf
flush_to_ldisc
In our system, the processing interval for each frame of IMU data
transmitted via UART can experience significant jitter due to this issue.
Instead of the expected 10 to 15 ms frame processing interval, we see
spikes up to 30 to 35 ms. Moreover, in just one or two hours, there can
be 2 to 3 occurrences of such high jitter, which is quite frequent. This
jitter exceeds the software's tolerable limit of 20 ms.
Introduce flip_wq in tty_port which can be set by tty_port_link_wq() or as
default linked to default workqueue allocated when tty_register_driver().
The default workqueue is allocated with flag WQ_SYSFS, so that cpumask and
nice can be set dynamically. The execution timing of tty_port_link_wq() is
not clearly restricted. The newly added function tty_port_link_driver_wq()
checks whether the flip_wq of the tty_port has already been assigned when
linking the default tty_driver's workqueue to the port. After the user has
set a custom workqueue for a certain tty_port using tty_port_link_wq(), the
system will only use this custom workqueue, even if tty_driver does not
have %TTY_DRIVER_CUSTOM_WORKQUEUE flag.
Introduce %TTY_DRIVER_CUSTOM_WORKQUEUE flag meaning not to create the
default single tty_driver workqueue. Two reasons why need to introduce the
%TTY_DRIVER_CUSTOM_WORKQUEUE flag:
1. If the WQ_SYSFS parameter is enabled, workqueue_sysfs_register() will
fail when trying to create a workqueue with the same name. The pty is an
example of this; if both CONFIG_LEGACY_PTYS and CONFIG_UNIX98_PTYS are
enabled, the call to tty_register_driver() in unix98_pty_init() will fail.
2. Different tty ports may be used for different tasks, which may require
separate core binding control via workqueues. In this case, the workqueue
created by default in the tty driver is unnecessary. Enabling this flag
prevents the creation of this redundant workqueue.
After applying this patch, we can set the related UART TTY flip buffer
workqueue by sysfs. We set the cpumask to CPU cores associated with the
IMU tasks, and set the nice to -20. Testing has shown significant
improvement in the previously described issue, with almost no stuttering
occurring anymore.
Signed-off-by: Xin Zhao <jackzxcui1989@163.com>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Link: https://patch.msgid.link/20251223034836.2625547-1-jackzxcui1989@163.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add support for HSIC USB mode, which can be set for second USB controller
and PHY on Tegra SoC along with already supported UTMI or ULPI.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Link: https://patch.msgid.link/20260122151125.7367-3-clamor95@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Refactor to directly use enum usb_phy_interface to determine the PHY mode.
This change is in preparation for adding support for HSIC mode.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Link: https://patch.msgid.link/20260122151125.7367-2-clamor95@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The port driver sets this bit for an alternate mode description to indicate
support for the mode selection feature. Once set, individual Alt Mode
drivers will no longer attempt to activate their respective modes within
their probe functions. This prevents race conditions and non-prioritized
activation.
The bit is not set by default. If left unset, the system retains the
current behavior where Alt Mode drivers manage their own activation logic.
Signed-off-by: Andrei Kuchynski <akuchynski@chromium.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://patch.msgid.link/20260119131824.2529334-6-akuchynski@chromium.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The mode selection process is controlled by the following API functions,
which allow to initiate and complete mode entry based on the priority of
each mode:
`typec_mode_selection_start` function compiles a priority list of supported
Alternate Modes.
`typec_altmode_state_update` function is invoked by the port driver to
communicate the current mode of the Type-C connector.
`typec_mode_selection_delete` function stops the currently running mode
selection process and releases all associated system resources.
`mode_selection_work_fn` task attempts to activate modes. The process stops
on success; otherwise, it proceeds to the next mode after a timeout or
error.
Signed-off-by: Andrei Kuchynski <akuchynski@chromium.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://patch.msgid.link/20260119131824.2529334-5-akuchynski@chromium.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch introduces a priority sysfs attribute to the USB Type-C
alternate mode port interface. This new attribute allows user-space to
configure the numeric priority of alternate modes managing their preferred
order of operation. If a new priority value conflicts with an existing
mode's priority, the priorities of the conflicting mode and all subsequent
modes are automatically incremented to ensure uniqueness.
Signed-off-by: Andrei Kuchynski <akuchynski@chromium.org>
Reviewed-by: Benson Leung <bleung@chromium.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://patch.msgid.link/20260119131824.2529334-4-akuchynski@chromium.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This new field in the port properties dictates whether the Platform Policy
Manager (PPM) allows the OS Policy Manager (OPM) to change the currently
active, negotiated alternate mode.
Signed-off-by: Andrei Kuchynski <akuchynski@chromium.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Benson Leung <bleung@chromium.org>
Link: https://patch.msgid.link/20260119131824.2529334-2-akuchynski@chromium.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Introduce a linked list tracking all inode connectors for a superblock.
We will use this list when the superblock is getting shutdown to
properly clean up all the inode marks instead of relying on scanning all
inodes in the superblock which can get rather slow.
Suggested-by: Amir Goldstein <amir73il@gmail.com>
Reviewed-by: Amir Goldstein <amir73il@gmail.com>
Reviewed-by: Christian Brauner <brauner@kernel.org>
Signed-off-by: Jan Kara <jack@suse.cz>
|
|
Add aes-gcm crypto API's for AMD/Xilinx Versal device.
Signed-off-by: Harsh Jain <h.jain@amd.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Add API to get SoC version and family info.
Signed-off-by: Harsh Jain <h.jain@amd.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
For better maintainability move crypto related API's to
new zynqmp-crypto.c file.
Signed-off-by: Harsh Jain <h.jain@amd.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Cross-merge networking fixes after downstream PR (net-6.19-rc7).
Conflicts:
drivers/net/ethernet/huawei/hinic3/hinic3_irq.c
b35a6fd37a00 ("hinic3: Add adaptive IRQ coalescing with DIM")
fb2bb2a1ebf7 ("hinic3: Fix netif_queue_set_napi queue_index input parameter error")
https://lore.kernel.org/fc0a7fdf08789a52653e8ad05281a0a849e79206.1768915707.git.zhuyikai1@h-partners.com
drivers/net/wireless/ath/ath12k/mac.c
drivers/net/wireless/ath/ath12k/wifi7/hw.c
31707572108d ("wifi: ath12k: Fix wrong P2P device link id issue")
c26f294fef2a ("wifi: ath12k: Move ieee80211_ops callback to the arch specific module")
https://lore.kernel.org/20260114123751.6a208818@canb.auug.org.au
Adjacent changes:
drivers/net/wireless/ath/ath12k/mac.c
8b8d6ee53dfd ("wifi: ath12k: Fix scan state stuck in ABORTING after cancel_remain_on_channel")
914c890d3b90 ("wifi: ath12k: Add framework for hardware specific ieee80211_ops registration")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
https://gitlab.freedesktop.org/drm/misc/kernel into drm-next
drm-misc-next for 6.20:
Core Changes:
- buddy: Fix free_trees memory leak, prevent a BUG_ON
- dma-buf: Start to introduce cgroup memory accounting in heaps, Remove
sysfs stats, add new tracepoints
- hdmi: Limit infoframes exposure to userspace based on driver
capabilities
- property: Account for property blobs in memcg
Driver Changes:
- atmel-hlcdc: Switch to drmm resources, Support nomodeset parameter,
various patches to use newish helpers and fix memory safety bugs
- hisilicon: Fix various DisplayPort related bugs
- imagination: Introduce hardware version checks
- renesas: Fix kernel panic on reboot
- rockchip: Fix RK3576 HPD interrupt handling, Improve RK3588 HPD
interrupt handling
- v3d: Convert to drm logging helpers
- bridge:
- Continuation of the refcounting effort
- new bridge: Algoltek AG6311
- panel:
- new panel: Anbernic RG-DS
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maxime Ripard <mripard@redhat.com>
Link: https://patch.msgid.link/20260122-antique-sexy-junglefowl-1bc5a8@houat
|
|
The stmmac implementation used by NXP for the i.MX8MP SoC is subject to
errata ERR050694. According to this errata, when no preamble byte is
transferred before the SFD from the PHY to the MAC, the MAC will discard
the frame.
Setting the PHY_F_KEEP_PREAMBLE_BEFORE_SFD flag instructs PHYs that
support it to keep the preamble byte before the SFD. This ensures that
the MAC successfully receives frames.
As this is an issue in the MAC implementation, only enable the flag for
the i.MX8MP SoC where the errata applies but not for other SoCs using a
working stmmac implementation.
The exact wording of the errata ERR050694 from NXP:
The IEEE 802.3 standard states that, in MII/GMII modes, the byte
preceding the SFD (0xD5), SMD-S (0xE6,0x4C, 0x7F, or 0xB3), or SMD-C
(0x61, 0x52, 0x9E, or 0x2A) byte can be a non-PREAMBLE byte or there can
be no preceding preamble byte. The MAC receiver must successfully
receive a packet without any preamble(0x55) byte preceding the SFD,
SMD-S, or SMD-C byte.
However due to the defect, in configurations where frame preemption is
enabled, when preamble byte does not precede the SFD, SMD-S, or SMD-C
byte, the received packet is discarded by the MAC receiver. This is
because, the start-of-packet detection logic of the MAC receiver
incorrectly checks for a preamble byte.
NXP refers to IEEE 802.3 where in clause 35.2.3.2.2 Receive case (GMII)
they show two tables one where the preamble is preceding the SFD and one
where it is not. The text says:
The operation of 1000 Mb/s PHYs can result in shrinkage of the preamble
between transmission at the source GMII and reception at the destination
GMII. Table 35-3 depicts the case where no preamble bytes are conveyed
across the GMII. This case may not be possible with a specific PHY, but
illustrates the minimum preamble with which MAC shall be able to
operate. Table 35-4 depicts the case where the entire preamble is
conveyed across the GMII.
This workaround was tested on a Verdin iMX8MP by enforcing 10 MBit/s:
ethtool -s end0 speed 10
Without keeping the preamble, no packet were received. With keeping the
preamble, everything worked as expected.
Signed-off-by: Stefan Eichenberger <stefan.eichenberger@toradex.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Link: https://patch.msgid.link/20260120203905.23805-4-eichest@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add a new flag, PHY_F_KEEP_PREAMBLE_BEFORE_SFD, to indicate that the PHY
shall not remove the preamble before the SFD if it supports it. MACs
that do not support receiving frames without a preamble can set this
flag.
Signed-off-by: Stefan Eichenberger <stefan.eichenberger@toradex.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Link: https://patch.msgid.link/20260120203905.23805-2-eichest@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The VF ID range of an SR-IOV device is [0, num_VFs - 1].
pci_ide_stream_alloc() mistakenly uses num_VFs to represent the last ID.
Fix that off by one error to stay in bounds of the range.
Fixes: 1e4d2ff3ae45 ("PCI/IDE: Add IDE establishment helpers")
Signed-off-by: Li Ming <ming.li@zohomail.com>
Reviewed-by: Xu Yilun <yilun.xu@linux.intel.com>
Link: https://patch.msgid.link/20260114111455.550984-1-ming.li@zohomail.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
The proposed ABI failed to account for multiple host bridges with the same
stream name. The fix needs to namespace streams or otherwise link back to
the host bridge, but a change like that is too big for a fix. Given this
ABI never saw a released kernel, delete it for now and bring it back later
with this issue addressed.
Reported-by: Xu Yilun <yilun.xu@linux.intel.com>
Reported-by: Yi Lai <yi1.lai@intel.com>
Closes: http://lore.kernel.org/20251223085601.2607455-1-yilun.xu@linux.intel.com
Link: http://patch.msgid.link/6972c872acbb9_1d3310035@dwillia2-mobl4.notmuch
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
Internal PCIe errors are not enabled by default during initialization
because their behavior is too device-specific and there is no standard way
to reason about them. However, for CXL an internal error is the standard
mechanism for conveying CXL protocol errors.
Export pci_aer_unmask_internal_errors() for CXL, but make it clear that
they are only meant for CXL and the status quo for leaving them masked for
PCIe in general remains.
Signed-off-by: Terry Bowman <terry.bowman@amd.com>
Reviewed-by: Dave Jiang <dave.jiang@intel.com>
Reviewed-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Reviewed-by: Jonathan Cameron <jonathan.cameron@huawei.com>
Link: https://patch.msgid.link/20260114182055.46029-10-terry.bowman@amd.com
Co-developed-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
|
|
CXL is a protocol that runs on top of PCIe electricals. Its error model
also runs on top of the PCIe AER error model by standardizing "internal"
errors as "CXL" errors. Linux has historically ignored internal errors.
CXL protocol error handling is then a task of enhancing the PCIe AER
core to understand that PCIe ports (upstream and downstream) and
endpoints may throw internal errors that represent standard CXL protocol
errors.
The proposed method to make that determination is to teach 'struct
pci_dev' to cache when its link has trained the CXL.mem and/or CXL.cache
protocols and then treat all internal errors as CXL errors. A design
goal is to not burden the PCIe AER core with CXL knowledge beyond just
enough to forward error notifications to the CXL RAS core. The forwarded
notification looks up a 'struct cxl_port' or 'struct cxl_dport'
companion device to the PCI device.
Introduce set_pcie_cxl() with logic checking for CXL.mem or CXL.cache
status in the CXL Flex Bus DVSEC status register. The CXL Flex Bus DVSEC
presence is used because it is required for all the CXL PCIe devices.[1]
[1] CXL 3.1 Spec, 8.1.1 PCIe Designated Vendor-Specific Extended
Capability (DVSEC) ID Assignment, Table 8-2
Signed-off-by: Terry Bowman <terry.bowman@amd.com>
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Reviewed-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Reviewed-by: Dave Jiang <dave.jiang@intel.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Alejandro Lucero <alucerop@amd.com>
Reviewed-by: Ben Cheatham <benjamin.cheatham@amd.com>
Reviewed-by: Dan Williams <dan.j.williams@intel.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://patch.msgid.link/20260114182055.46029-4-terry.bowman@amd.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
|
|
Add macros to convert between ratio and percentage related units,
including percent (1/100), permille (1/1,000), permyriad (1/10,000,
also equivalent to one Basis point) and per cent mille (1/100,000).
Those are Used for precise fractional calculations in engineering,
finance, and measurement applications.
Signed-off-by: Jonathan Santos <Jonathan.Santos@analog.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Add guard classes for iio_device_claim_*() conditional locks. This will
aid drivers write safer and cleaner code when dealing with some common
patterns.
These classes are not meant to be used directly by drivers (hence the
__priv__ prefix). Instead, documented wrapper macros are provided to
enforce the use of ACQUIRE() or guard() semantics and avoid the
problematic scoped guard.
Suggested-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Reviewed-by: David Lechner <dlechner@baylibre.com>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Signed-off-by: Kurt Borja <kuurtb@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Implement iio_device_claim_buffer_mode() fully inline with the use of
__iio_dev_mode_lock(), which takes care of sparse annotations.
To completely match iio_device_claim_direct() semantics, we need to
also change iio_device_claim_buffer_mode() return semantics to usual
true/false conditional lock semantics.
Additionally, to avoid silently breaking out-of-tree drivers, rename
iio_device_claim_buffer_mode() to iio_device_claim_try_buffer_mode().
Reviewed-by: David Lechner <dlechner@baylibre.com>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Signed-off-by: Kurt Borja <kuurtb@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
In order to eventually unify the locking API, implement
iio_device_claim_direct() fully inline, with the use of
__iio_dev_mode_lock(), which takes care of sparse annotations.
Reviewed-by: David Lechner <dlechner@baylibre.com>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Signed-off-by: Kurt Borja <kuurtb@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Add unconditional wrappers around the internal IIO mode lock.
As mentioned in the documentation, this is not meant to be used by
drivers, instead this will aid in the eventual addition of cleanup
classes around conditional locks.
Reviewed-by: David Lechner <dlechner@baylibre.com>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Signed-off-by: Kurt Borja <kuurtb@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Needed for some stubs to prevent build issues if !CONFIG_I3C
|
|
devres_for_each_res() is only used by .../firmware_loader/main.c, which
already includes base.h.
The usage of devres_for_each_res() by code outside of driver-core is
questionable, hence move it to base.h.
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://patch.msgid.link/20260119162920.77189-1-dakr@kernel.org
Signed-off-by: Danilo Krummrich <dakr@kernel.org>
|
|
The AXP717 has some extra registers related to type-C CC pin
negotiation. They were missing from the original submission.
Add them for completeness.
Signed-off-by: Chen-Yu Tsai <wens@kernel.org>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://patch.msgid.link/20251225080241.3153453-1-wens@kernel.org
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
The TPS65214 PMIC variant has a LOCK_REG register that prevents writes to
nearly all registers when locked. Unlock the registers at probe time and
leave them unlocked permanently.
This approach is justified because:
- Register locking is very uncommon in typical system operation
- No code path is expected to lock the registers during runtime
- Adding a custom regmap write function would add overhead to every
register write, including voltage changes triggered by CPU OPP
transitions from the cpufreq governor which could happen quite
frequently
Cc: stable@vger.kernel.org
Fixes: 7947219ab1a2d ("mfd: tps65219: Add support for TI TPS65214 PMIC")
Reviewed-by: Andrew Davis <afd@ti.com>
Signed-off-by: Kory Maincent (TI.com) <kory.maincent@bootlin.com>
Link: https://patch.msgid.link/20251218-fix_tps65219-v5-1-8bb511417f3a@bootlin.com
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
As there are some registers missing which are required for future charger
extensions, add them.
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Reviewed-by: Matti Vaittinen <mazziesaccount@gmail.com>
Link: https://patch.msgid.link/20251207085024.7375-1-andreas@kemnade.info
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
tps6105x_mode
Fix spelling of an enum to fix a kernel-doc warning.
Fix kernel-doc of struct tps6105x to prevent kernel-doc warnings.
Warning: include/linux/mfd/tps6105x.h:68 Enum value 'TPS6105X_MODE_TORCH'
not described in enum 'tps6105x_mode'
Warning: include/linux/mfd/tps6105x.h:68 Excess enum value
'%TPS61905X_MODE_TORCH' description in 'tps6105x_mode'
Warning: include/linux/mfd/tps6105x.h:93 struct member 'pdata'
not described in 'tps6105x'
Warning: include/linux/mfd/tps6105x.h:93 struct member 'client'
not described in 'tps6105x'
Fixes: 798a8eee44da ("mfd: Add a core driver for TI TPS61050/TPS61052 chips v2")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Link: https://patch.msgid.link/20251125022750.3165569-1-rdunlap@infradead.org
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
'ib-mfd-regulator-6.20' and 'ib-mfd-rtc-6.20' into ibs-for-mfd-merged
|
|
This reverts commit 2b69987be575 ("sched: Add
task_struct->faults_disabled_mapping"), which added this field without
review or maintainer signoff. With bcachefs removed from the
tree it is also unused now.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://patch.msgid.link/20260122085223.487092-1-hch@lst.de
|
|
Provide the actual decision function, which decides whether a time slice
extension is granted in the exit to user mode path when NEED_RESCHED is
evaluated.
The decision is made in two stages. First an inline quick check to avoid
going into the actual decision function. This checks whether:
#1 the functionality is enabled
#2 the exit is a return from interrupt to user mode
#3 any TIF bit, which causes extra work is set. That includes TIF_RSEQ,
which means the task was already scheduled out.
The slow path, which implements the actual user space ABI, is invoked
when:
A) #1 is true, #2 is true and #3 is false
It checks whether user space requested a slice extension by setting
the request bit in the rseq slice_ctrl field. If so, it grants the
extension and stores the slice expiry time, so that the actual exit
code can double check whether the slice is already exhausted before
going back.
B) #1 - #3 are true _and_ a slice extension was granted in a previous
loop iteration
In this case the grant is revoked.
In case that the user space access faults or invalid state is detected, the
task is terminated with SIGSEGV.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://patch.msgid.link/20251215155709.195303303@linutronix.de
|
|
When a time slice extension was granted in the need_resched() check on exit
to user space, the task can still be scheduled out in one of the other
pending work items. When it gets scheduled back in, and need_resched() is
not set, then the stale grant would be preserved, which is just wrong.
RSEQ already keeps track of that and sets TIF_RSEQ, which invokes the
critical section and ID update mechanisms.
Utilize them and clear the user space slice control member of struct rseq
unconditionally within the existing user access sections. That's just an
unconditional store more in that path.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Link: https://patch.msgid.link/20251215155709.131081527@linutronix.de
|
|
If a time slice extension is granted and the reschedule delayed, the kernel
has to ensure that user space cannot abuse the extension and exceed the
maximum granted time.
It was suggested to implement this via the existing hrtick() timer in the
scheduler, but that turned out to be problematic for several reasons:
1) It creates a dependency on CONFIG_SCHED_HRTICK, which can be disabled
independently of CONFIG_HIGHRES_TIMERS
2) HRTICK usage in the scheduler can be runtime disabled or is only used
for certain aspects of scheduling.
3) The function is calling into the scheduler code and that might have
unexpected consequences when this is invoked due to a time slice
enforcement expiry. Especially when the task managed to clear the
grant via sched_yield(0).
It would be possible to address #2 and #3 by storing state in the
scheduler, but that is extra complexity and fragility for no value.
Implement a dedicated per CPU hrtimer instead, which is solely used for the
purpose of time slice enforcement.
The timer is armed when an extension was granted right before actually
returning to user mode in rseq_exit_to_user_mode_restart().
It is disarmed, when the task relinquishes the CPU. This is expensive as
the timer is probably the first expiring timer on the CPU, which means it
has to reprogram the hardware. But that's less expensive than going through
a full hrtimer interrupt cycle for nothing.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Link: https://patch.msgid.link/20251215155709.068329497@linutronix.de
|
|
The kernel sets SYSCALL_WORK_RSEQ_SLICE when it grants a time slice
extension. This allows to handle the rseq_slice_yield() syscall, which is
used by user space to relinquish the CPU after finishing the critical
section for which it requested an extension.
In case the kernel state is still GRANTED, the kernel resets both kernel
and user space state with a set of sanity checks. If the kernel state is
already cleared, then this raced against the timer or some other interrupt
and just clears the work bit.
Doing it in syscall entry work allows to catch misbehaving user space,
which issues an arbitrary syscall, i.e. not rseq_slice_yield(), from the
critical section. Contrary to the initial strict requirement to use
rseq_slice_yield() arbitrary syscalls are not considered a violation of the
ABI contract anymore to allow onion architecture applications, which cannot
control the code inside a critical section, to utilize this as well.
If the code detects inconsistent user space that result in a SIGSEGV for
the application.
If the grant was still active and the task was not preempted yet, the work
code reschedules immediately before continuing through the syscall.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://patch.msgid.link/20251215155709.005777059@linutronix.de
|
|
Provide a new syscall which has the only purpose to yield the CPU after the
kernel granted a time slice extension.
sched_yield() is not suitable for that because it unconditionally
schedules, but the end of the time slice extension is not required to
schedule when the task was already preempted. This also allows to have a
strict check for termination to catch user space invoking random syscalls
including sched_yield() from a time slice extension region.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Link: https://patch.msgid.link/20251215155708.929634896@linutronix.de
|
|
Implement a prctl() so that tasks can enable the time slice extension
mechanism. This fails, when time slice extensions are disabled at compile
time or on the kernel command line and when no rseq pointer is registered
in the kernel.
That allows to implement a single trivial check in the exit to user mode
hotpath, to decide whether the whole mechanism needs to be invoked.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://patch.msgid.link/20251215155708.858717691@linutronix.de
|
|
Extend the quick statistics with time slice specific fields.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://patch.msgid.link/20251215155708.795202254@linutronix.de
|
|
Guard the time slice extension functionality with a static key, which can
be disabled on the kernel command line.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://patch.msgid.link/20251215155708.733429292@linutronix.de
|
